Electronic Test

WV Communications 70-01FM-CH FM Modulation Sensitivity Adjust 70MHz RF

SKU:

39369

Availability:

Usually ships within 1-2 business days.

Weight:

6.00 LBS

Brand:

WV Communications

Model:

70-01FM-CH

MPN:

70-01FM-CH

Secondary Model:

70MDF-FM-BRZ

SKU:

39369

Type:

FM Modulation Sensitivity Adjust Unit

Frequency:

70 MHz

RF Output Connector:

BNC (J2)

Tone Input Connector:

BNC (J1)

Control Interface:

DB9 (J4)

AC Input Connector:

IEC C14 (J3)

Power Requirements:

115 VAC, 1-Phase, 47-63Hz, 1A

Fuse:

1A SB

Front Panel Indicators:

AC PWR ON (green LED), FAULT (red LED)

Front Panel Controls:

FM Modulation Sensitivity Adjust (rotary trim pot)

Power Switch:

Rear-panel rocker switch (AC ON / AC OFF, SW1)

Form Factor:

Benchtop / Rackmount enclosure

Condition:

Used – Inspected

Seller Notes:

Unit only; no accessories included.

Country/Region of Manufacture:

United States

Condition Notes:

WV Communications 70-01FM-CH FM Modulation Sensitivity Adjust. Inspected and in good used condition. Clean enclosure with minor surface wear. Front panel controls and rear BNC/DB9 connectors intact. No damage observed.

California Prop 65 Warning:

WARNING: This product can expose you to chemicals including lead and lead compounds, and DEHP (a phthalate), which are known to the State of California to cause cancer and birth defects or other reproductive harm. Go to P65Warnings.ca.gov

FMT CMD/RNG Select Unit 12-Port BNC Video Switcher RF Modulation Satcom Rack

FMT

SKU:

39365

Availability:

Usually ships within 1–2 business days.

Weight:

14.00 LBS

Brand:

Unbranded

Model:

CMD/RNG Select Unit

MPN:

2586-BA

Type:

Video Select Switcher / RF Signal Router

SKU:

39365

Condition:

Used – Pulled from Working Environment

Number of Ports:

12 BNC + 1 D-Sub (J14)

Connector Type:

BNC (J2–J13), D-Sub 25-pin (J14), IEC AC inlet (J1)

Power Requirements:

120 VAC, 1A, 47–440Hz

Power Entry Module:

Corcom 6VM1S F7361A, 6A 120V 47-440Hz

Internal Relay:

R30D-E1Z4-24V, 24VDC coil

Form Factor:

Rackmount (2U approx.)

Front Panel Functions:

RTP IN: T&C RNG, XPNDR RNG; RTP LM TONES; RNG/CMD; SCG/CG

Signal Routing:

Inputs to FM Modulators via BNC

Application:

Satellite command/ranging signal routing to FM modulators

Hardware Revision:

REV 1

Seller Notes:

Unit only; no cables or accessories included.

Country/Region of Manufacture:

United States

Condition Notes:

FMT CMD/RNG Select Unit BNC video switcher. Inspected, good used condition. Pulled from a working satcom environment. All BNC ports and front-panel switches appear intact. See photos.

California Prop 65 Warning:

WARNING: This product can expose you to chemicals including lead and lead compounds, and DEHP (a phthalate), which are known to the State of California to cause cancer and birth defects or other reproductive harm. Go to P65Warnings.ca.gov

Vertex RSI DCS3-002-1-243 C-Band Downconverter 4372.5-5258.5 MHz Satcom 1U

Vertex RSI

SKU:

39345

Availability:

Usually ships within 1-2 business days.

Weight:

16.00 LBS

Brand:

Vertex RSI

Model:

DCS3-002-1-243

MPN:

DCS3-002-1-243

Secondary Model:

ISS-2000-5318-1A

Customer Part Number:

A13249-5318-1A

CTI Part Number:

ISS-2000-5318-1A

SKU:

39345

Type:

C-Band Satellite Downconverter

Frequency Range:

4372.5 - 5258.5 MHz

Frequency Band:

C-Band

Form Factor:

1U Rackmount

Power Requirements:

90-250V AC, 2A, 47-63 Hz

Interface Type:

RS-232, D-Sub (DB-15), BNC RF/IF Monitor

Front Panel:

LCD display, numeric keypad, LCL/ENT/MENU keys, ALARM LED

Rear Connectors:

IEC AC inlet, DB-9 (J4/J5), DB-15 (J6), BNC (J2/J3), GND

Software Revision:

SCD107 (visible on front LCD)

CAGE Code:

59530

Work Order:

32260

Condition:

Used – Pulled from Working Environment

Seller Notes:

Unit only; pulled from working satcom installation

Country/Region of Manufacture:

United States

Application:

Satellite ground station, C-Band receive chain

Condition Notes:

This Vertex RSI DCS3-002-1-243 C-Band Downconverter is in good used condition. Pulled from a working satcom installation where it was in active use. Chassis shows normal surface wear. Front panel and rear connectors intact.

California Prop 65 Warning:

WARNING: This product can expose you to chemicals including lead and lead compounds, and DEHP (a phthalate), which are known to the State of California to cause cancer and birth defects or other reproductive harm. Go to P65Warnings.ca.gov

Hughes 3582710-100-1 Westar FM Data Detector Satellite Ground Station TM

Hughes

SKU:

39340

Availability:

Usually ships within 1-2 business days.

Weight:

17.00 LBS

Brand:

Hughes Aircraft

Model:

3582710-100-1

MPN:

3582710-100-1

Type:

FM Data Detector

SKU:

39340

System:

Westar

Division:

Hughes Satellite Ground Equipment Division

Condition:

Used – Inspected and in Good Condition

Seller Notes:

Unit only; inspected and in good condition. See photos for connector and control details.

Form Factor:

Rackmount

Front Panel Indicators:

PS1, MIP, EX status LEDs

Front Panel Controls:

Nutation Offset knob, Nutation Gain switch (100Hz/V, 1kHz/V), Nutation/Earth button

Connector - Input:

J1: Composite TM IN (BNC)

Connector - Output 1:

J2: Detected TM Data OUT (D-sub)

Connector - Output 2:

J3: PSI OUT (BNC)

Analog Data Output:

Analog Data output on front panel

Power:

AC Power with ON/OFF toggle switch and GND terminal

Application:

Westar satellite ground station telemetry data detection

Country/Region of Manufacture:

United States

Condition Notes:

Hughes 3582710-100-1 Westar FM Data Detector. Inspected and in good condition. Light wear from prior rack use. Front panel controls, LEDs, and connectors intact. Rear BNC/D-sub connectors undamaged. Interior boards and wiring appear clean.

California Prop 65 Warning:

WARNING: This product can expose you to chemicals including lead and lead compounds, and DEHP (a phthalate), which are known to the State of California to cause cancer and birth defects or other reproductive harm. Go to P65Warnings.ca.gov

Rockwell 8548-00 Power Supply w/ 2 Wescom 401 Wire Line Amplifiers 24/48VDC

Rockwell

SKU:

39339

Availability:

Usually ships within 1-2 business days.

Weight:

18.00 LBS

Brand:

Rockwell

Model:

8548-00

MPN:

8548-00

Secondary Model:

Wescom 401

Type:

DC Power Supply with Wire Line Amplifier Modules

SKU:

39339

Input Voltage:

105-130VAC

Input Frequency:

60Hz

Input Power:

95 Watts

Output Voltage:

24VDC or 48VDC (selectable)

Output Current:

1.25 Amps

Number of Amplifier Modules:

2

Amplifier Module Model:

Wescom 401 Wire Line Amplifier

Fuse Rating:

1.5A Slo-Blo

Output Selector:

24V / 48V switchable via rear panel switch

Form Factor:

Modular / Benchtop Stack

Application:

Telephone carrier / wireline telecom systems

Condition:

Used – Inspected and in Good Condition

Seller Notes:

Includes Rockwell 8548-00 power supply and qty 2 Wescom 401 wire line amplifier modules

Country/Region of Manufacture:

United States

Condition Notes:

Rockwell 8548-00 Power Supply with 2 Wescom 401 Wire Line Amplifiers. Inspected, in good used condition. Minor surface wear on chassis. AC power cord included. Both amplifier modules present.

California Prop 65 Warning:

WARNING: This product can expose you to chemicals including lead and lead compounds, and DEHP (a phthalate), which are known to the State of California to cause cancer and birth defects or other reproductive harm. Go to P65Warnings.ca.gov

Microdyne 1400-MR 106-912-01 Telemetry Receiver PM Demod RF Tuner 50-90MHz 4U

Microdyne

SKU:

39335

Availability:

Usually ships within 1–2 business days.

Weight:

60.00 LBS

Brand:

Microdyne

Model:

1400-MR

MPN:

106-912-01

Secondary Model:

1400-MRA

Type:

Telemetry Receiver

SKU:

39335

Condition:

Used – Pulled from Working Environment

Seller Notes:

Includes PM Demodulator 1451-D, IF Filter Amp 1420-I, RF Tuner 1411-VT(70)

Country/Region of Manufacture:

United States

Form Factor:

Rack Mount, 4U, 19-inch

Power Requirements:

120V AC, 50–60 Hz, 1.5A SLC-BLC

RF Frequency Range:

50–90 MHz (VT Tuner)

Plugin Module 1:

PM Demodulator – 1451-D

Plugin Module 2:

IF Filter Amplifier – 1420-I Series

Plugin Module 3:

RF Tuner – 1411-VT(70), 50–90 MHz

Interface / Connectivity:

RS-232 (J2G), Accessory Port (J2C), BNC outputs

Demodulation Modes:

FM, PM, AFC, VFO, XTAL, 2nd LO

Bandwidth Options:

0.100, 0.500, 1.00 MHz, N/U

Output Types:

AM, SDU, Record, Pre-D, CFM, Video, AGC

PROM Config Date:

4-17-90

PROM Part Number:

106-261-77

Application:

Satellite / SatCom / Microwave / RF Telemetry

Compatible With:

19-inch EIA standard rack enclosures

Loop Width Settings:

2B, 30, 100, 300, 1K, 3K, 10K Hz

Condition Notes:

Microdyne 1400-MR Telemetry Receiver pulled from a working environment where it was in active use and functional. Inspected and in good used condition. All three plugin modules present. Please contact us with questions.

California Prop 65 Warning:

WARNING: This product can expose you to chemicals including lead and lead compounds, and DEHP (a phthalate), which are known to the State of California to cause cancer and birth defects or other reproductive harm. Go to P65Warnings.ca.gov

3dbm 70MDF-DAT-GLW Dual-Channel 70MHz FM Satcom Signal Modulator 19" Rack

3dbm

SKU:

39334

Availability:

Usually ships within 1-2 business days.

Weight:

35.00 LBS

Brand:

3dbm

Model:

70MDF-DAT-GLW

MPN:

70MDF-DAT-GLW

Secondary Model:

70MDF-GLW / 50AT-1-2R

Type:

Dual-Channel 70MHz FM Satcom Signal Modulator

SKU:

39334

Condition:

Used – Pulled from Working Environment

Form Factor:

19" Rack Mount Chassis

Number of Channels:

2

Modulation Type:

FM (Frequency Modulation)

Center Frequency:

70 MHz

Plug-In Module 1:

3dbm 70MDF-GLW FM Modulator

Plug-In Module 2:

3dbm 50AT-1-2R Dual RF Attenuator

Plug-In Module 3:

3dbm 70MDF-GLW FM Modulator

Internal Sub-Assembly 1:

3DBM INC. 70MDF-GLW-MOD 70MHz FM Modulator

Internal Sub-Assembly 2:

3DBM INC. 70MDF-GLW-EQ Equalizer

RF Connector Type:

BNC (Tone In, Main RF Out, Range Calib RF Out)

Serial Interface:

DB9 (J4, J5 — RS-232 control)

AC Power Connector:

IEC C14 (J6 – AC Input) with fuse pull

Front Panel Controls:

Operate/Calibrate, Equalize/Linear switches; LED indicators

RF Attenuation Control:

Dual rotary attenuators: FM Modulator 1 & 2 RF Attenuation

Rear Connections per Module:

Tone Input (J1), Main RF Output (J2), Range Calib RF Out (J3)

Attenuator Module Ports:

RF 1 In (J1), RF 1 Out (J2), RF 2 In (J3), RF 2 Out (J4)

Application:

Satellite Ground Station / Satcom Uplink Signal Modulation

Seller Notes:

Includes 19" chassis with two 70MDF-GLW modulator plug-ins and one 50AT-1-2R dual attenuator plug-in.

Country/Region of Manufacture:

United States

Condition Notes:

3dbm 70MDF-DAT-GLW dual-channel 70MHz FM satcom modulator. Inspected, in good condition. Pulled from a working environment where it was in active use and functional. All three plug-ins present. Please view photos and contact us with questions.

California Prop 65 Warning:

WARNING: This product can expose you to chemicals including lead and lead compounds, and DEHP (a phthalate), which are known to the State of California to cause cancer and birth defects or other reproductive harm. Go to P65Warnings.ca.gov

Hughes 3582710-100 Westar Palapa FM Data Detector HAC Satellite Ground Equip

Hughes

SKU:

39333

Availability:

Usually ships within 1-2 business days.

Weight:

17.00 LBS

Brand:

Hughes Aircraft

Model:

3582710-100

MPN:

3582710-100

Type:

FM Data Detector

SKU:

39333

Product Code:

HAC FM DD

System Compatibility:

Westar / Palapa Satellite Ground System

Division:

Hughes Satellite Ground Equipment Division

Condition:

Used – Inspected; missing top and bottom covers

Power Requirements:

110 VAC

Form Factor:

Rackmount

Front Panel Indicators:

PSI, MIP, EX LED indicators

Front Panel Controls:

Nutation Offset & Gain knobs; Analog Data switch

Rear Connectors:

J1 BNC (Composite TM In), J2 D-Sub (Detected TM Data Out), J3 BNC (PSI Out)

Seller Notes:

Includes power cable (jacket damaged — see photos). Missing top and bottom covers.

Country/Region of Manufacture:

United States

Condition Notes:

Hughes 3582710-100 FM Data Detector. Inspected, good used condition. Missing top and bottom covers; internal PCB exposed. Rear connectors intact. Included power cable has damaged jacket — replace before use.

California Prop 65 Warning:

WARNING: This product can expose you to chemicals including lead and lead compounds, and DEHP (a phthalate), which are known to the State of California to cause cancer and birth defects or other reproductive harm. Go to P65Warnings.ca.gov

WV Communications 70-01FD-CH 19" Rackmount 70 MHz FM Modulator RF/IF Demodulator

WV Communications

SKU:

39331

Availability:

Usually ships within 1-2 business days.

Weight:

21.00 LBS

Brand:

WV Communications

Model:

70-01FD-CH

MPN:

70-01FD-CH

Secondary Model:

70-01FM-CH

Type:

19" Rackmount FM Modulator / RF-IF Demodulator Chassis

SKU:

39331

Condition:

Used – Inspected

Seller Notes:

Includes 70MDF-FM-BRZ 70 MHz FM Modulator and RF/IF-DEM-PANAM Demodulator modules

Form Factor:

19" Rackmount

Number of Modules:

2

Module 1 Part Number:

70MDF-FM-BRZ

Module 1 Description:

70 MHz FM Modulator

Module 2 Part Number:

RF/IF-DEM-PANAM

Module 2 Description:

RF/IF Demodulator

Center Frequency:

70 MHz (69.6 / 70.0 MHz selectable)

Modulation Type:

FM (Frequency Modulation)

Power Requirements:

115 VAC, 1-Phase, 47-63 Hz

Fuse Rating:

1A SB

Front Panel Indicators:

AC PWR ON (green LED), FAULT (red LED)

Front Panel Controls:

FM Modulation Sensitivity Adjust; FM Demod Output Level Adjust

RF Input Frequency Select:

69.6 MHz / 70.0 MHz

Tone Monitor Connector:

BNC (front panel, demodulator module)

Rear Connectors – Demodulator:

J1 RF Input (BNC), J2 Tone Output (BNC), J3 AC Input (IEC), J4 (DB9)

Rear Connectors – Modulator:

J1 Tone Input (BNC), J2 RF Output (BNC), J3 AC Input (IEC), J4 (DB9)

AC Power Switch:

SW1 rocker switch (AC ON / AC OFF) per module

Country/Region of Manufacture:

United States

Condition Notes:

WV Communications 70-01FD-CH rackmount chassis inspected and in good condition. Both modules present: 70 MHz FM Modulator (70MDF-FM-BRZ) and RF/IF Demodulator (RF/IF-DEM-PANAM). Light rack wear. Contact us with questions.

California Prop 65 Warning:

WARNING: This product can expose you to chemicals including lead and lead compounds, and DEHP (a phthalate), which are known to the State of California to cause cancer and birth defects or other reproductive harm. Go to P65Warnings.ca.gov

Hughes 3899311-100 Westar VII Range Tone Processor Rackmount Satcom

Hughes

SKU:

39329

Availability:

Usually ships within 1-2 business days.

Weight:

35.00 LBS

Brand:

Hughes Aircraft

Model:

3899311-100

MPN:

3899311-100

Type:

Range Tone Processor

SKU:

39329

System:

Westar VII

Revision:

Rev A

Division:

Satellite Ground Equipment Division

Form Factor:

Rack Mount

Tone Frequencies:

27777, 3472, 434, 54.25 Hz

Front Panel Controls:

Mode, Input, OSC, Measure, Tones, Phase Count display

OSC Modes:

Internal / External

Input Modes:

Normal / Test

Mode Options:

Computer / Manual; Master / Slave

EXT OSC IN:

BNC connector on front panel

Condition:

As-Is / For Parts or Not Working

Seller Notes:

Sold as-is. Does not power on. Unit only, no accessories.

Country/Region of Manufacture:

United States

Condition Notes:

Hughes 3899311-100 Westar VII Range Tone Processor does not power on. Tested at our facility — failed to power up. Sold as-is for parts or repair only. No functionality guaranteed. Please see photos.

California Prop 65 Warning:

WARNING: This product can expose you to chemicals including lead and lead compounds, and DEHP (a phthalate), which are known to the State of California to cause cancer and birth defects or other reproductive harm. Go to P65Warnings.ca.gov

3dbm 70MDF-DAT-BRZ Dual Port RF AM Satcom FM Modulator Plugin Chassis 70MDF-BRZ

3dbm

SKU:

39328

Availability:

Usually ships within 1–2 business days.

Weight:

35.00 LBS

Brand:

3dbm

Model:

70MDF-DAT-BRZ

MPN:

70MDF-DAT-BRZ

Secondary Model:

70MDF-BRZ

SKU:

39328

Type:

Dual Port RF AM Satcom FM Modulator Plugin Chassis

Condition:

Used – Inspected and Tested

Plugin 1 Model:

70FMO-DL-1-3-A-1 FM Modulator

Plugin 2 Model:

50AT-1-2R RF Attenuator

Plugin 3 Model:

70MDF-BRZ FM Modulator/Controller

Included Component:

JFW Industries 50DR-003 RF component (internal)

Form Factor:

Rackmount Plugin Chassis

Number of Plugin Slots:

3

Signal Type:

RF AM / FM

Application:

Satellite Communications (Satcom) Uplink

Rear Connectors - FM Modulator:

BNC RF Out (J5), BNC MOD IN (J6), DB9 Status (J7), AC Power (J8)

Rear Connectors - Attenuator:

BNC RF1 Input (J1), BNC RF1 Output (J2), BNC RF2 Input (J3), BNC RF2 Output (J4)

Rear Connectors - Main Module:

BNC Tone Input (J1), BNC Main RF Output (J2), BNC Range Calib RF Output (J3), DB9 (J4)

Power Requirements:

105–125 VAC, 60 Hz; Fuse 2A

Front Panel Controls:

Operate/Calibrate switch, RF attenuation knobs (FM Mod 1 & 2), indicators

RF Attenuation Range:

0–40 dB (per FM Modulator attenuator dial)

Country/Region of Manufacture:

United States

Compatible With:

Satcom Uo Upconverter, RF Amplifier systems

Seller Notes:

Chassis with three installed plugin modules as described. Tested working.

Condition Notes:

3dbm 70MDF-DAT-BRZ Satcom FM Modulator Plugin Chassis tested and confirmed working with a compatible Uo Converter and RF Amplifier. All three plugins installed. Normal wear. Unit shipped may vary from photo.

California Prop 65 Warning:

WARNING: This product can expose you to chemicals including lead and lead compounds, and DEHP (a phthalate), which are known to the State of California to cause cancer and birth defects or other reproductive harm. Go to P65Warnings.ca.gov

Hughes 3814115-100 Galaxy Range Tone Processor 28.44 MHz Rackmount Satcom

Hughes

SKU:

39327

Availability:

Usually ships within 1-2 business days.

Weight:

32.00 LBS

Brand:

Hughes Aircraft

Model:

3814115-100

MPN:

3814115-100

Type:

Range Tone Processor

SKU:

39327

System:

Galaxy

Revision:

Rev A

Frequency:

28.44 MHz

Form Factor:

Rackmount

Manufacturer Division:

Hughes Satellite Ground Equipment Division

Oscillator Mode:

Internal / External switchable

Input Mode:

Normal / Test switchable

Operating Mode:

Computer / Manual switchable

Tone Frequencies:

277.7, 507.2, 434, 54.25 Hz (front panel buttons)

Measure Control:

Start / Stop

Phase Count Display:

Front panel phase count readout

Computer Interface:

D-sub connector (J2, 25-pin)

Rear Connectors:

J2 Computer, J3 Receiver, J4 Analog Ø Out, J5 T&C

Rear Connectors 2:

J6 Transponder, J7 Status, J8 Computer In, J9 Computer Out

Rear Connectors 3:

J10 Analog Ø Out (TP), J11 Range Tone Out (TP), J12 RCVR Input

Rear Connectors 4:

J13 OSC Freq, E1 Chassis GND, E2 Signal GND, S1 AC Power On/Off

Internal Power Module:

Acopian PB15-50 AC to DC Power Module

AC Power:

IEC AC inlet with power switch (rear panel)

Application:

Satellite range tone generation and phase measurement

Condition:

Used – Pulled from Working Environment

Country/Region of Manufacture:

United States

Seller Notes:

Unit only; pulled from working satcom environment. No accessories included.

Condition Notes:

Hughes 3814115-100 Galaxy Range Tone Processor in good used condition. Pulled from a working satcom environment. Inspected; front panel controls and rear BNC connectors appear intact. Please contact us with any questions.

California Prop 65 Warning:

WARNING: This product can expose you to chemicals including lead and lead compounds, and DEHP (a phthalate), which are known to the State of California to cause cancer and birth defects or other reproductive harm. Go to P65Warnings.ca.gov

Microdyne 1151-D(B)(B) Anti-Sideband Wide Angle PM Demodulator Satcom RF

Microdyne

SKU:

39322

Availability:

Usually ships within 1–2 business days.

Weight:

5.00 LBS

Brand:

Microdyne

Model:

1151-D(B)(B)

MPN:

1N51D(B)(B)D

Type:

Wide Angle Anti-Sideband PM Demodulator

SKU:

39322

Condition:

Used – Pulled from Working Environment

Seller Notes:

Unit only; no accessories observed. Photos show unit as-received.

Country/Region of Manufacture:

United States

Form Factor:

Modular / Plug-In Module

Modulation Type:

Phase Modulation (PM)

Demodulator Mode:

Anti-Sideband Wide Angle / Wide Band

Loop Bandwidth Range:

10, 30, 100, 300, 1000 Hz (switchable)

Loop Modes:

Open Loop / Closed Loop

Search Mode:

Auto / Manual Search

AGC Modes:

NORM / TRACK

Output Type:

PM Output

Rear Connector:

D-Sub 25-pin (P3); PI and TI connectors

Front Controls:

Loop Bandwidth switch, Fine Tune dial, Loop Lock, Noise, BAL, Lock indicators

Application:

RF Satcom Earth Station Systems

Manufacturer Location:

Microdyne Corporation, Rockville, MD 20850

Condition Notes:

Microdyne 1151-D(B)(B) Wide Angle PM Demodulator. Inspected, in good used condition. Pulled from a working satcom environment. Surface scratches on enclosure; front-panel controls and rear D-Sub connector intact.

California Prop 65 Warning:

WARNING: This product can expose you to chemicals including lead and lead compounds, and DEHP (a phthalate), which are known to the State of California to cause cancer and birth defects or other reproductive harm. Go to P65Warnings.ca.gov

Decom Systems DSI 7376 PSK/PCM Bit Synchronizer PSK Demodulator Rackmount

Decom Systems

SKU:

39320

Availability:

Usually ships within 1-2 business days.

Weight:

18.00 LBS

Brand:

Decom Systems Inc.

Model:

7376

MPN:

7376-41000-012

Secondary Model:

010226-1F EVO-0380 EVO-0491

Type:

PSK/PCM Bit Synchronizer & PSK Demodulator

SKU:

39320

Form Factor:

Rackmount (2U)

Application:

Telemetry Data Acquisition, Aerospace/Defense

Signal Type:

PSK, PCM

PCM Codes Supported:

NRZ-L, NRZ-M, NRZ-S, Bi-Phase-L, Bi-Phase-M, PN

Carrier Frequency:

32 kHz

Bit Rate Range:

1 kbps – 4.8 kbps (BR1–BR6 selectable)

Bandwidth Settings:

BW1: 750 Hz, BW2: 1.5 kHz, BW3: 3 kHz, BW4: 6 kHz

Loop Setting:

1% / 0.1% selectable

Input Bandwidth Control:

Narrow / Wide switchable

Input Source:

1 / 2 selectable

Front Panel Outputs (Test):

Bit Sync / Data In, Data Out, Clock Out (BNC)

Rear Panel Connectors:

J1–J13 BNC: Demod In 1/2, Bit Sync Ext In, NRZL Out, Clock Out, Demod Status Out, Bit Sync Status Out, Bib Tape Out, PN Tape Out

Power Input Select:

S1 switch: 115V / 230V / 0.5A (rear panel)

Grounds:

Signal Ground (J12), Chassis Ground (J13) on rear

Country/Region of Manufacture:

United States

Seller Notes:

Unit only; no manual or accessories included.

Condition:

Used – Inspected, appears in good condition

Condition Notes:

Decom Systems DSI 7376 PSK/PCM Bit Synchronizer has been inspected and appears in good used condition. Front panel controls and BNC connectors intact. Normal cosmetic wear. PanamSat/PAS Capital asset tags present. Please contact us with questions.

California Prop 65 Warning:

WARNING: This product can expose you to chemicals including lead and lead compounds, and DEHP (a phthalate), which are known to the State of California to cause cancer and birth defects or other reproductive harm. Go to P65Warnings.ca.gov

Precise Sensors 111-2-1000-01-G-35-10-B6 Pressure Transducer 0-1000 PSIG

Precise Sensors

SKU:

39242

Availability:

Usually ships within 1-2 business days.

Weight:

1.00 LBS

Brand:

Precise Sensors

Model:

111-2-1000-01-G-35-10-B6

MPN:

111-2-1000-01-G-35-10-B6

Type:

Pressure Transducer

SKU:

39242

Pressure Range:

0-1000 PSIG

Pressure Type:

Gauge (PSIG)

Output Connector:

6-pin circular connector

Process Connection:

Male threaded port (front)

Body Material:

Stainless Steel

Manufacturer Location:

Monrovia, CA 91016

Country/Region of Manufacture:

United States

Form Factor:

Inline / In-line body

Condition:

Used – Inspected and Pulled from Working Environment

Seller Notes:

Transducer only; no additional accessories included.

Condition Notes:

Precise Sensors 111-2-1000-01-G-35-10-B6 0-1000 PSIG pressure transducer. Inspected; good used condition. Stainless body shows minor scuffing. Connector pins clean and intact. No damage to process port or body.

California Prop 65 Warning:

WARNING: This product can expose you to chemicals including lead and lead compounds, and DEHP (a phthalate), which are known to the State of California to cause cancer and birth defects or other reproductive harm. Go to P65Warnings.ca.gov

Federal Products EMD-6000 Surfanalyzer 600 & System 2000 25-2020-00 Surface

Federal

SKU:

39232

Availability:

Usually ships within 1-2 business days.

Weight:

190.00 LBS

Brand:

Federal Products

Model:

EMD-6000

Secondary Model:

25-2020-00

MPN:

EMD-6000 B10

Product Line:

Surfanalyzer 600 / Surfanalyzer System 2000

Type:

Surface Roughness Analyzer / Profilometer

SKU:

39232

Condition:

Used – Inspected and Tested

Seller Notes:

Two-unit system: Surfanalyzer 600 (EMD-6000) + System 2000 (25-2020-00); includes interconnect cable

Country/Region of Manufacture:

United States

Form Factor:

Benchtop

Power Requirements (EMD-6000):

115V, 60Hz, 10W

Power Requirements (25-2020-00):

115V, 60Hz, 250W

Controller Fuse Rating:

1/4A @ 115V / 1/8A @ 230V, SLO-BLO

Measurement Type:

Surface Roughness and Waviness (Ra / CLA)

Measurement Parameters:

Ra (CLA), Waviness (W), Profile, Roll-Off

Roughness Cutoff:

0.025, 0.076, 0.25, 0.76 mm (selectable)

Waviness Cutoff:

0.076, 0.25, 0.76 mm (selectable)

Traverse Speed:

Slow 0.254 mm/sec / Fast 2.54 mm/sec

Chart Speed:

Selectable in/sec and mm/sec

Sensitivity / Stylus Position:

100, 200, 500, 1K µin/div; 0.02–5 µm/div

Display Type:

LED digital readout + integrated chart recorder

Recorder Channels:

Channel A and Channel B

Rear Connectors (EMD-6000):

PROBE, INPUT PROBE/AUX switch, AUX (DB15), TRAVERSE

Rear Connectors (25-2020-00):

PRINT, INPUT, AUX (DB connectors); EXT (card-edge)

ALM Compatible:

Yes

Schematic Reference:

289868

Application:

Surface finish and roughness measurement in manufacturing QC

Compatible With:

Federal Products Surfanalyzer probes and stylus assemblies

Condition Notes:

Federal Products EMD-6000 Surfanalyzer 600 & System 2000 (25-2020-00) surface roughness analyzer. Powered on and inspected — appears in good working condition. Both units power on. Interconnect cable included. Normal lab wear. See photos.

California Prop 65 Warning:

WARNING: This product can expose you to chemicals including lead and lead compounds, and DEHP (a phthalate), which are known to the State of California to cause cancer and birth defects or other reproductive harm. Go to P65Warnings.ca.gov

Tele-Path Industries 108-DS1 DS1 Test Access Module ESF B8ZS AMI TPI w/ Case

Tele-Path Industries

SKU:

39217

Availability:

Usually ships within 1-2 business days.

Weight:

3.00 LBS

Brand:

Tele-Path Industries

Model:

108-DS1

MPN:

108-DS1

SKU:

39217

Type:

DS1 Test Access Module

Condition:

Used – Inspected

Seller Notes:

Includes gray TPI branded carry case

Form Factor:

Portable / Handheld

Country/Region of Manufacture:

United States

Interface Type:

DS1 / T1

Line Coding:

ESF, SF, B8ZS, AMI, DDS, VF, SLC1

Signal Access:

East (Primary) and West (Aux.) TX/RX

Function:

Drop & Insert, DS1 Signal Monitoring

Signaling:

A, B, C, D Signaling Bits with LED indicators

Channel Selection:

Up/Down Channel buttons with LED display

Connector Type:

Mini DIN power, bantam jacks (DS1 access)

Compatible With:

T1/DS1 circuits, East/West span access

Includes:

Gray TPI carry case

Condition Notes:

Tele-Path Industries 108-DS1 DS1 Test Access Module inspected and in good used condition. Blue enclosure shows light wear. All front-panel controls and ports appear intact. Includes gray TPI carry case. Please contact us with any questions.

California Prop 65 Warning:

WARNING: This product can expose you to chemicals including lead and lead compounds, and DEHP (a phthalate), which are known to the State of California to cause cancer and birth defects or other reproductive harm. Go to P65Warnings.ca.gov

Filter Concepts 3E20-F 3X20A EMI Filter 250/440VAC 50/60Hz Three Phase

Filter Concepts

SKU:

39159

Availability:

Usually ships within 1-2 business days.

Weight:

6.00 LBS

Brand:

Filter Concepts

Model:

3E20-F

MPN:

3E20 F

Type:

Three-Phase EMI / RFI Line Filter

SKU:

39159

Voltage Rating:

250/440VAC

Current Rating:

20A per phase (3x20A)

Phase:

Three Phase

Frequency:

50/60Hz

Number of Phases:

3

Connector / Termination Type:

Screw terminals (N, A, B, C)

Certifications:

UL Listed, CSA Listed

Date Code:

9744 / 7143

Seller Notes:

New open-box unit in original cardboard packaging.

Country/Region of Manufacture:

United States

Condition:

New – Open Box

Condition Notes:

Filter Concepts 3E20-F 3X20A EMI Filter. New and unused; original cardboard packaging shows storage wear but unit is uninstalled and in new condition. Screw terminals clean and undamaged.

California Prop 65 Warning:

WARNING: This product can expose you to chemicals including lead and lead compounds, and DEHP (a phthalate), which are known to the State of California to cause cancer and birth defects or other reproductive harm. Go to P65Warnings.ca.gov

Radio Electronics RE530 RDS Generator IEEE-488 GPIB Memory Bus BNC 220V

Radio Electronics

SKU:

38968

Availability:

Usually ships within 1-2 business days.

Weight:

40.00 LBS

Brand:

RE Instruments AS

Model:

RE530

MPN:

RE530

Type:

RDS Generator

SKU:

38968

Country/Region of Manufacture:

Denmark

Form Factor:

Benchtop

Power Requirements:

220V / 110-120V AC, 47-63Hz, 70VA

Interface Type:

IEEE-488 (GPIB), Memory Bus, Clock/Data, Terminal

Output Connectors:

BNC (Composite, Sync, Component)

Function Keys:

RDS, VRF, TP, BK, TA, DK, CT, TEST

Menu Keys:

VRF Menu, RDS Menu, CAL Menu, AUX Menu

Display:

LED: Function (Phase), Value, Deviation (kHz)

Serial Number (Label):

R00N01

Seller Notes:

Powers on with display illumination. IEEE-488 and Memory Bus interfaces installed.

Condition Notes:

RE530 RDS Generator powers on with display lit. Pulled from working broadcast environment. Light cosmetic wear, buttons and connectors intact. Not fully tested. As-inspected condition.

Display Type:

LED Indicators

LED Indicators:

Function (Phase), Value, Deviation (kHz)

Serial Number:

R00N01

Condition:

Used – Pulled from Working Environment

California Prop 65 Warning:

WARNING: This product can expose you to chemicals including lead and lead compounds, and DEHP (a phthalate), which are known to the State of California to cause cancer and birth defects or other reproductive harm. Go to P65Warnings.ca.gov

MSA 96104 Cell Assembly Battery Reference Voltage Source SPC 083 REV 0 Gas

MSA

SKU:

38871

Availability:

Usually ships within 1-2 business days.

Weight:

5.00 LBS

Brand:

MSA

Model:

96104

MPN:

96104

Secondary Model:

SPC 083 REV 0

Type:

Cell Assembly / Battery Reference Voltage Source

SKU:

38871

Condition:

As-Is / For Parts or Not Working

Seller Notes:

Sold as-is. Includes dual flow tubes, multi-conductor wiring harness, and BNC-style gas port connector.

Document Reference:

SPC 083 REV 0 / Part No. 469022

Application:

MSA Gas Detection Instrument Reference Cell

Included Accessories:

Dual vertical flow tubes, multi-conductor harness, BNC-type gas fitting

Form Factor:

Freestanding Module / Bench Component

Country/Region of Manufacture:

United States

Condition Notes:

MSA 96104 Cell Assembly sold as-is for parts or repair. Appears complete with flow tubes, wiring harness, and gas connector present. Not tested, not guaranteed functional. Age-related wear visible. Please contact us with questions.

California Prop 65 Warning:

WARNING: This product can expose you to chemicals including lead and lead compounds, and DEHP (a phthalate), which are known to the State of California to cause cancer and birth defects or other reproductive harm. Go to P65Warnings.ca.gov