Description
Vitronics Soltec ISO5006 5-Zone Solder Reflow Oven 208V 3-Phase 65A 20" Belt SMT
The Vitronics ISO5006 is a floor-standing, forced-convection solder reflow oven for surface-mount (SMT) printed circuit board assembly. A wire mesh conveyor carries populated, paste-printed boards through a series of independently controlled heating zones and then a cooling section, so the solder paste follows a preheat, soak, reflow, and cooldown thermal profile. This unit has five thermocouple profile jacks, a five-meter gas flow bank, a top-mounted exhaust duct, and an Anafaze-based control system in the electrical cabinet. It is supplied without the host computer or control software.
Specifications & What's Included
- Manufacturer: Vitronics (the controller module is marked Vitronics Soltec)
- Model: ISO5006 (rating plate name: Reflow)
- Electrical rating: 208V, 3-phase, 60Hz, 65A
- Largest load: 30A
- AIC rating: 10kA
- Maximum temperature: 350°C
- Conveyor: wire mesh belt, 20 inches wide
- Heating zones: 5 (matching the five-meter flow bank and five profile thermocouple jacks)
- Profile thermocouple jacks: 5x type K (Chromel/Alumel), labeled 1 through 5
- Gas flow bank: 5x Dwyer variable-area flow meters, scaled 0-50 SCFM AIR, each with a blue-handled Nibco ball shutoff valve, on a side-mounted aluminum panel with copper supply manifold
- Nitrogen atmosphere capability via the five-zone flow meter bank
- Cooling section: three axial cooling fans mounted above the conveyor at the belt end
- Exhaust: top-mounted exhaust duct with elbow; two fan guards on top of the hood
- Hood: lift controls with Hood Engage pushbutton and Down/Up selector; hood shown raised on a support rod
- Operator controls: Power On, e-stop, Alarm Condition lamp, Silence Alarm, Rail Width Adjust, Board Support Adjust, Conveyor Override
- Control system: Anafaze Measurement & Control System module (Vitronics Soltec marked) with relay/terminal board
- Power section: Siemens contactor with overload relay, DIN-rail circuit breakers, control transformer and terminal blocks
- Auxiliary outlets: 4x 110 VAC outlets on side panel
- Overall dimensions: 93" L x 60" W x 75" H
- Form factor: floor-standing conveyor oven
- Country of manufacture: United States
- Not included: computer, control software, manuals
Applications
The ISO5006 is a Vitronics (Soltec) convection reflow oven. Its Anafaze-based control, thermocouple profiling jacks, and wire mesh conveyor are consistent with the late-1990s to 2000s generation of production SMT reflow equipment. Ovens of this type sit between the pick-and-place machine and inspection or test in a surface-mount line.
- Industries & settings: electronics contract manufacturing, SMT prototype and pilot lines, aerospace and defense electronics assembly, and repair or rework departments.
- Typical applications: reflow soldering of paste-printed PCB assemblies, thermal profiling with type K thermocouples to verify peak temperature and time above liquidus, and low-oxidation reflow where inert gas is plumbed through the flow meter bank.
- Compatible systems: in-line SMT conveyor lines with a 20" belt, using stencil printers and pick-and-place machines upstream. A host PC and control software must be sourced for operation.
This Vitronics ISO5006 floor-standing convection solder reflow oven has been inspected and is in good used condition. The conveyor, heating zones, exhaust duct, and gas flow meter bank are all present and intact. The cabinet shows normal wear from production use, and the photos show the electrical cabinets and the control panel. The oven does not include a computer, control software, or manuals, so a PC and compatible control software or a third-party control solution will need to be sourced separately. Please view our photo set and contact us if you have any questions.
Warranty Information
Additional Information
Brand: |
Vitronics |
Model: |
ISO5006 |
MPN: |
ISO5006 |
Type: |
Convection Solder Reflow Oven |
SKU: |
45033 |
Seller Notes: |
Does not include computer, control software, or manuals |
Country/Region of Manufacture: |
United States |
Voltage: |
208V |
Current Rating: |
65A |
Phase: |
Three Phase |
Frequency: |
60Hz |
Largest Load: |
30A |
AIC Rating: |
10KA |
Belt Width: |
20 inches |
Max Temperature: |
350°C |
Application: |
PCB / SMT Solder Reflow |
Nitrogen Capable: |
Yes — five-zone gas flow meter bank |
Number of Zones: |
5 (per 5-meter flow bank and 5 profile jacks) |
Conveyor Type: |
Wire mesh conveyor belt |
Exhaust: |
Top-mounted exhaust duct connection |
Control Panel Features: |
E-stop, hood up/down, rail width, board support, alarm |
Auxiliary Outlets: |
4x 110 VAC outlets on side panel |
Overall Dimensions: |
93" L x 60" W x 75" H |
Form Factor: |
Floor-standing conveyor oven |
Condition: |
Used – Inspected, good condition; no computer or software included |
Condition Notes: |
Vitronics ISO5006 solder reflow oven in good used condition. Conveyor, heating zones, exhaust and gas flow meter bank are present and intact. Computer, control software and manuals are not included. |
California Prop 65 Warning: |
WARNING: This product can expose you to chemicals including lead and lead compounds, and DEHP (a phthalate), which are known to the State of California to cause cancer and birth defects or other reproductive harm. Go to P65Warnings.ca.gov |
Heating Method: |
Forced Convection |
Controller: |
Anafaze Measurement & Control System module |
Profile Thermocouple Jacks: |
5x Type K (Chromel/Alumel) |
Cooling Section: |
3 axial cooling fans over conveyor at one end |
Flow Meters: |
5x Dwyer, 0-50 SCFM AIR scale, Nibco ball valves |