SMA Custom

Custom Stainless SMA Coaxial Feedthrough Vacuum Chamber Flange 6-Port 18 GHz

(No reviews yet) Write a Review
SKU:
27975
Condition:
Used
Availability:
Currently out of stock — contact us for availability.
Weight:
3.00 LBS
Shipping:
Calculated at Checkout
  • Custom stainless SMA coaxial feedthrough vacuum chamber flange — top view showing 6 SMA connectors arranged in a circle with central pin and peripheral mounting holes
  • Custom stainless SMA feedthrough vacuum flange — bottom/N-connector side showing recessed bowl profile with 6 connector ends and machined rim
  • Close-up of SMA connector side — gold center conductors visible inside precision-machined SMA port housings on stainless vacuum feedthrough flange
  • Close-up of recessed side — SMA connector tips with gold pins and counterbored recesses visible on underside of stainless coaxial vacuum feedthrough
  • Side profile of custom stainless SMA coaxial feedthrough flange — full plate thickness visible with SMA connectors protruding from both faces
$200.00

This item is temporarily unavailable. Please view our recommended, in-stock alternatives directly below.

Description

Custom Stainless SMA Coaxial Feedthrough Vacuum Chamber Flange 6-Port 18 GHz

This is a custom-machined stainless steel sector cap designed as a coaxial signal feedthrough for vacuum chambers. It provides six SMA RF ports through a single vacuum flange plate, allowing RF and microwave signals to pass into or out of a vacuum environment while maintaining a sealed boundary. The construction is precision-machined from stainless steel with a substantial, well-finished form factor suggesting it was made for a research or industrial vacuum system.

Specifications & What's Included

  • Material: Stainless steel, custom-machined
  • Outer diameter: 121 mm
  • Plateau diameter (N-connector side): 110 mm, with a 5.4 mm recess around the perimeter
  • SMA connector side recess inner diameter: 92.8 mm
  • Connector circle diameter: 61 mm (6 SMA ports arranged on this bolt circle)
  • Number of coaxial feedthrough ports: 6 × SMA
  • Central screw (N-connector side): 19 mm tall (approx. 3/4 in), 11 mm diameter, 20 TPI
  • Plate thickness at periphery: 0.400 in (approx. 10.2 mm)
  • Mass: approximately 1 lb 15 oz (0.88 kg)
  • Frequency rating: approximately 18 GHz based on connector construction (not bench-tested)
  • Center conductors: gold-plated, visibly intact in all six ports
  • Mounting: peripheral bolt holes visible around the rim for chamber attachment
  • Included: flange only — no mating SMA connectors, cables, or mounting hardware

Applications

SMA coaxial feedthroughs like this are used in vacuum systems — including physical vapor deposition (PVD) chambers, sputtering systems, ion beam systems, and research vacuum vessels — to route RF and microwave signals between the vacuum interior and external instrumentation without breaking the vacuum seal. Six-port feedthrough plates are commonly used in plasma diagnostics, RF plasma excitation, network analyzer measurements inside a chamber, or any application requiring multiple simultaneous coaxial signal paths through a single vacuum port. The SMA connector format supports frequencies from DC to 18 GHz (connector-dependent), making these suitable for microwave and millimeter-wave measurements in vacuum. Custom-machined stainless feedthrough plates of this type are typically built to order for specific chamber flanges, and finding a pre-made unit that fits an existing system can save significant lead time and fabrication cost. The dimensional detail in the listing (outer diameter, connector placement circle, plate thickness, thread specs) should allow direct comparison to an existing chamber opening.

Condition: For Parts or Not Working
This custom stainless steel SMA coaxial feedthrough vacuum chamber flange has been inspected and is in good used condition. The machined stainless body shows light handling marks consistent with prior lab use, but the surface finish is clean and the connector housings show no visible damage. The six SMA connectors are high quality — the gold center conductors are bright and intact as seen in the photos. RF performance has not been tested at our facility; the ~18 GHz rating is based on connector construction rather than a verified measurement. Please review all photos carefully and contact us with any questions.
View AllClose

Warranty Information

We stand behind every item we sell with a 30-day money-back guarantee. If your item arrives not as described, you may return it within 30 days for a full refund. Please inspect your purchase upon arrival and contact us with any questions.
View AllClose

Additional Information

Brand:
Unbranded
Model:
Custom SMA Coaxial Feedthrough Vacuum Flange
Type:
Coaxial Feedthrough / Vacuum Chamber Flange
SKU:
27975
Connector Type:
SMA (6 ports)
Number of Ports:
6
Outer Diameter:
121 mm
Plateau Diameter:
110 mm (5.4 mm recess on N-connector side)
Connector Circle Diameter:
61 mm
SMA Recess Inner Diameter:
92.8 mm
Plate Thickness (periphery):
0.400 in (approx. 10.2 mm)
Central Screw Height:
19 mm (3/4 in)
Central Screw Diameter:
11 mm, 20 TPI
Material:
Stainless Steel
Frequency Rating:
Up to ~18 GHz (untested)
Compatible With:
Vacuum deposition chambers, research vacuum systems
Application:
RF signal feedthrough for vacuum chambers
Country/Region of Manufacture:
Unknown
Seller Notes:
Flange only — no mating SMA connectors or cables included
Condition Notes:
This custom stainless SMA coaxial feedthrough vacuum chamber flange is in good used condition. Light handling marks on the body; SMA connectors appear clean with intact gold pins. RF performance untested — ~18 GHz rating based on connector type.
California Prop 65 Warning:
WARNING: This product can expose you to chemicals including lead and lead compounds, and DEHP (a phthalate), which are known to the State of California to cause cancer and birth defects or other reproductive harm. Go to P65Warnings.ca.gov
View AllClose